19:14 rezny 

Update Mesa to 17.0.3

* OpenGL 4.5 support for RadeonSI and recent Intel
* Use LLVM 4.0 by default, building with 3.9 is possible via MESA_LLVM_VER
* DRI3 remains enabled at compile time, but is now disabled at runtime for
  stock FreeBSD.  Set LIBGL_DRI3_ENABLE in the environment to enable DRI3.
  This extra check is added when compiling on stock FreeBSD, not DRM-next.
  This change was made to work around a problem in libEGL, which fails to
  fall back to using DRI2 when run on a system without DRI3 support.

Reviewed by:	jmd, mat
Approved by:	swills (mentor)
Differential Revision:	https://reviews.freebsd.org/D10250

 

16:57 rezny 

Update to 13.0.6

- Allow use of newer LLVM, i.e. llvm40, via MESA_LLVM_VER in make.conf [1]
- Disable use of LLVM on platforms where it's known not to be available [2]

PR:		[1] 217016, [2] 216944
Reported by:	[1] greenreaper@hotmail.com, [2] linimon
Approved by:	swills (mentor)
Differential Revision:	https://reviews.freebsd.org/D10183

 

15:49 rezny 

Add one sed command, courtesy of madpilot, to replicate a section of changes
that were over-eagerly trimmed from patch-configure in the last commit.

Approved by:	swills (mentor)
Differential Revision:	https://reviews.freebsd.org/D9555

 

13:31 rezny 

Update Mesa to 13.0.4

* Use LLVM 3.9
* OpenGL 4.4 support for recent Intel and ReadeonSI

PR:	214581
Approved by:	swills (mentor)
Differential Revision:	https://reviews.freebsd.org/D9438

 

11:30 kwm 

Update mesa to 11.0.8.

 * Depend on libelf on DragonFly
 * Rework the vdpau support code and enable vdpau for DragonFly, FreeBSD
   doesn't support it just yet.
 * Revert commit that removed support for non-render nodes. Neither
   FreeBSD nor DragonFly supports render nodes at this time.
 * Fix LDFLAGS to work with GCC5, which DragonFly uses by default.
 * Update Makefile.targets: ffast-math isn't used since 8.0.3, don't
   replace x86_64 with amd64 on Dragonfly. Drop obsolete python disable
   replace.

 

18:56 kwm 

Improve the sed replace, so it doesn't clobber 2>&1 redirection.

Submitted by:	Wolfgang Jenkner <wjenkner@inode.at>

 

21:04 kwm 

Update Mesa to 10.6.9.

* Unbreak build on powerpc and other !x86 archs by moving the
  --with-dri-drivers logic from dri/Makefile to the
  libGL/Makefile.common file. So the settings are applied to all mesa ports,
  this was missed in the 10.6.6 update. [1]
* Don't try to enable OpenCL support on anything other then i386 and amd64. [1]
* Move the texture-float and vdpau logic to Makefile.common even if the latter
  isn't supported yet. Keep OPTIONS_DEFINE/DEFAULT in dri/Makefile since they
  need to defined before bsd.port.options.mk is included, and they only affect
  the dri modules.
* Sed on 11 and 10 supports \< and \> however sed on 9.x and dragonfly do not,
  replace the sed keywords with some magic to get the intended results. [2]

Submitted by:		marino@ [2]
Reported and tested by:	arved@ (on ppc32)[1]

 

18:07 kwm 

Update Mesa port to 10.6.6 and add Clover.
Add beignet 1.1.0.
Add clinfo, clblas, clfft and clrng.

The major change is that all Mesa ports are now configured the same way.
This fixes several problems and enables new features.  The details
are described in this blog post:
http://blogs.freebsdish.org/graphics/2015/03/18/unifying-mesa-ports-configure/

The second important change is the OpenCL support.  Mesa's
implementation, Clover, is enabled as well as Beignet.  Clover
targets all Gallium drivers, only Radeon GPUs in our case.  Beignet
is for Intel GPUs starting with Ivy Bridge.  Thanks to Johannes
Dieterich, O. Hartman, and Koop Mast for their work on OpenCL!  As a
bonus, there are several OpenCL-based math ports added (clblas,

(Only the first 15 lines of the commit message are shown above )